what be this thingy and were do e belong. thingy.JPG 95.54KB 0 downloads
4Tx Part I.d.
#1
Posted 06 September 2019 - 01:58 pm
#2
Posted 06 September 2019 - 02:01 pm
Loom guidance? Beverage holder. Hmmm. Definitely TDM?
If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117
Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.
Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.
#3
Posted 06 September 2019 - 02:12 pm
Don't recognise it. Def not a bit shared with mk1.
Loom guidance? Beverage holder. Hmmm. Definitely TDM?
Might not be TDM but I thought I'd better check as it's the only bit left over from the parts box and I sort of recognise it. MOT next week hopefully.
#4
Posted 06 September 2019 - 05:32 pm
It might be the routing bracket for the front brake lines and speedo cable on the front forks (Ta Mr Eccles). Could someone check and maybe post photo to check fitment arrangement.
Ta Muchly
#5
Posted 06 September 2019 - 05:33 pm
spyball alarm/immob, bluespot brake calipers and Stainless hoses, Fournales air adjustable shock with Remote Resevoir, forks raised 10mm thru yokes, racetech linear fork springs in 15 wt oil, Kappa wingrack/luggage, heated grips, Kedo handguards, dual heat controller to power heated jacket liner and or pants!!, Stebel 136DB horn, K&N air filter, colour matched Baglux tank cover (magnetic tank bag modified to fit cover), osram +50% headloight bulbs, headlight protector,"NitramSpecial" parking loight, tail light indicators all running on LED's & incorporate "Lite Buddies", MK7 Scottoiler fitted, taller screen, 2-2 stainless steel CCC's, Devil stainless down pipes. MKI Renntec engine crash bars & sump guard.
engine changed july 2007 on a dyno run it made 79.1BHP / Torque 59.9Had a brief flirtation with a 1999 MKIIa but it blew an exaust valve on the M5 so was sold on to be repaired.
I loike tay and hang sangwiches !
www.kenhogantreeservices.co.uk
http://s33.photobuck...77/wickla/?sc=6
http://reg.imageshack.us/v_images.php
#6
Posted 06 September 2019 - 05:46 pm
If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117
Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.
Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.
#7
Posted 06 September 2019 - 09:29 pm
Tink it's prolly attached to the headstock to route the loom.
Thats what I think too
"As I Lay Rubber down to street, I pray for traction I can keep. But if I skid and begin to slide, please dear god protect my ride"
Mods; Oil pressure switch, neoprene rear inner mudguard, scottoiler, highway pegs, fenda extenda, 1999 carbs and airbox, Kais suspension setup, later clutch springs, LED lamps, Metmachex swingarm, Hagon Shock, Oxford heated grips, 4 way fused accessory Bus, 17" 3CV front wheel, Michellin R6 tyres, GPS speedo, 5' ignition advance.
#8
Posted 07 September 2019 - 08:18 am
found the location for the mystery bracket, see part 21.
https://www.motorcyc...torcycles/frame
Boop
#9
Posted 07 September 2019 - 11:48 am
If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117
Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.
Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users