Yes I'm sure that would be fun. If it worked it would mean that K-line dash units might be interchangeable (with some tweaking)
Tdm-Duino (Midnight Project)
#21
Posted 12 May 2017 - 09:02 pm
900 with better bits. Owes me nothing, Makes me smile
#22
Posted 22 May 2017 - 08:06 pm
The resistor is wired in series with the IAT, virtually on the back of it's plug
I added a resistor today, i must say its made a great deal of difference to the rideability, its almost smooth!!!! Im considering advancing the timing too. Sorry dont mean to hijack the thread, what JBX is doing is head crunching!!!
#23
Posted 22 May 2017 - 08:11 pm
I added a resistor today, i must say its made a great deal of difference to the rideability, its almost smooth!!!! Im considering advancing the timing too. Sorry dont mean to hijack the thread, what JBX is doing is head crunching!!!
I've been running it for a couple of thousand miles, i checked the plugs last week to check the colour (also because I have 4 degrees timing advance) and they looked perfect. The residue inside the exhaust pipe was still grey, not black and overly sooty, so it is only a small change.
900 with better bits. Owes me nothing, Makes me smile
#24
Posted 22 May 2017 - 08:17 pm
Thats reassuring to know, thanks.
#25
Posted 23 May 2017 - 09:00 am
This project is brilliant!
I have been working on an arduino based data logger for my track bike using the following:
At Mega
Adafruit ultimate GPS datalogger shield
Bosch BN055 6 axis accelerometer shield
The data I am trying to capture for a kick off is:
GPS position
speed
rate of acceleration/deceleration
lean angle
TPS
Brake (just the switch at the moment but I would like to introduce a brake pressure sensor at some point.)
all this is to be output to a csv file where I can overlay the telemetry data onto my videos for analysis.
Further expansions to this are things like adding IR temp sensors pointing at the front and rear wheels so I have tyre temp data,
Great to have some other people interested in this sort of stuff as I am current on my own and a bit of a novice!
Hello by the way - its been a long time (circa 12 years) but I am back with a TDM 900!
#26
Posted 23 May 2017 - 10:28 am
This project is brilliant!
I have been working on an arduino based data logger for my track bike using the following:
At Mega
Adafruit ultimate GPS datalogger shield
Bosch BN055 6 axis accelerometer shield
The data I am trying to capture for a kick off is:
GPS position
speed
rate of acceleration/deceleration
lean angle
TPS
Brake (just the switch at the moment but I would like to introduce a brake pressure sensor at some point.)
all this is to be output to a csv file where I can overlay the telemetry data onto my videos for analysis.
Further expansions to this are things like adding IR temp sensors pointing at the front and rear wheels so I have tyre temp data,
Great to have some other people interested in this sort of stuff as I am current on my own and a bit of a novice!
Hello by the way - its been a long time (circa 12 years) but I am back with a TDM 900!
are ya stihl a GAAAAAAAAAAAAAAAAY ???? welcome back Coxylaaaaaaaaaaaaaaaaaaaaad xxx
spyball alarm/immob, bluespot brake calipers and Stainless hoses, Fournales air adjustable shock with Remote Resevoir, forks raised 10mm thru yokes, racetech linear fork springs in 15 wt oil, Kappa wingrack/luggage, heated grips, Kedo handguards, dual heat controller to power heated jacket liner and or pants!!, Stebel 136DB horn, K&N air filter, colour matched Baglux tank cover (magnetic tank bag modified to fit cover), osram +50% headloight bulbs, headlight protector,"NitramSpecial" parking loight, tail light indicators all running on LED's & incorporate "Lite Buddies", MK7 Scottoiler fitted, taller screen, 2-2 stainless steel CCC's, Devil stainless down pipes. MKI Renntec engine crash bars & sump guard.
engine changed july 2007 on a dyno run it made 79.1BHP / Torque 59.9Had a brief flirtation with a 1999 MKIIa but it blew an exaust valve on the M5 so was sold on to be repaired.
I loike tay and hang sangwiches !
www.kenhogantreeservices.co.uk
http://s33.photobuck...77/wickla/?sc=6
http://reg.imageshack.us/v_images.php
#27
Posted 23 May 2017 - 10:40 am
Now then Wicky lad!
Been a long time, but I will have you know I was never a gay, I had a hardcore mk1!
I am a full on 900 gayer now though haha
Edited by Coxylaad, 23 May 2017 - 10:43 am.
#28
Posted 23 May 2017 - 02:07 pm
Sorry for that brief interruption to your thread crazy Frenchman. :-)
If you want to mark your location on the Carpe map: http://www.carpe-tdm...opic.php?t=5117
Doin valve clearances? Use dappers valve shim exchange program and the job will be carroty - Free (other than you postin me yer shims) for sporting members.
Active member of TPLQHCSRSFC and TSRMCMAS (even though a year off) and avid fan of PM not sent.
#29
Posted 23 May 2017 - 02:07 pm
With a firm rear end so I hear.
Mk2a 2000 in Silver. Top end Refurb @ 41100 miles, Scottoiler, Renthal Road High Bars, Up & Back Bar Risers, Bellypan, DL650 Handguards, Capt. Picard Bar Ends, House of Henty SS Wheel spacers, New Seat Cover Fitted. 58 MPG !! Now owned by chrisbee ! Studley's mk2a Bloggerydoodaah ! Photos of my first MK1 Photos of my MK2a TPLQHCSRSFC No. 1 Fan
#30
Posted 23 May 2017 - 02:14 pm
#31
Posted 23 May 2017 - 02:20 pm
What happens on CMC doesn't stay on CMC.
Mk2a 2000 in Silver. Top end Refurb @ 41100 miles, Scottoiler, Renthal Road High Bars, Up & Back Bar Risers, Bellypan, DL650 Handguards, Capt. Picard Bar Ends, House of Henty SS Wheel spacers, New Seat Cover Fitted. 58 MPG !! Now owned by chrisbee ! Studley's mk2a Bloggerydoodaah ! Photos of my first MK1 Photos of my MK2a TPLQHCSRSFC No. 1 Fan
#32
Posted 02 August 2017 - 07:58 pm
any update on this?
#34
Posted 03 August 2017 - 01:43 pm
nice - dont get sand in your electronics!
#35
Posted 09 February 2018 - 02:15 pm
any progress?
#36
Posted 10 February 2018 - 10:33 pm
Still working on it !
Joke apart, I'm very busy these days and not much time for the project.
Latest update : I've switched to an Arduino Mega 2560 because it has more GPIO & analog inputs for the sensors, and also more program memory.
Still with the 2x16 chars display, but I'll also change the display for a 84x48 pixels Nokia lcd display.
If anybody needs the C++ source code, I'll post it on the web.
Works ok, needs some tweaking for sensors calibration...
Edited by JBX, 10 February 2018 - 10:34 pm.
#37
Posted 19 February 2018 - 01:26 pm
i wouldnt mind having a look at the code please
#39
Posted 20 February 2018 - 06:37 am
Did I just witness Carpe's longest ever post?
I'm sorry to interrupt, I wasn't expecting it!
As you were, me teas nearly ready.
TDM 850 Loud and unusual. CRM 250r Woo hoo! DT 230 Lanza Fiddled with.... Bloody hell, is that legal? GG Randonee AKA "I didn't think that was possible".
#40
Posted 20 February 2018 - 09:23 am
He obviously ate far to much mint jelly last night eh and dappers makes more sense ya ask me
Bigred mk1 R1 Calipers- Braided lines- Givi wing rack-Crash bungs- Hi vis bullets-PR2's- and a hoot to ride.
Quad 900 Silver Laser duo tech pipes-Scott oiler-Engine crash bars- Radiator mounted see me ring LED's-Datatool system 3 alarm -Centre stand- Extender fender-Renthal bars-Handle bar risers-Mirror extenders-BMW GS Handgaurds-Acumen uprated horn & Nautilus-Stainless steel Radiator guard-Givi wing rack-OEM screen-Yammy touring screen-MRA Vario-MRA Double bubble cut down for fast as fk riding-Tiger screen-Tank protector-Stomp grip panels-Optimate lead Gone to Heaven
1991 MK1 in need of some TLC watch this space Sorted and on the Road Mick it's the bike that Jack built Gone to Heaven
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users