Jump to content


Photo

Carby Balancer (home made)


  • Please log in to reply
8 replies to this topic

#1 masterbrewer

masterbrewer

    has been here 4ever

  • Member
  • PipPipPipPipPipPipPipPip
  • 1,553 posts
  • Location:Adelaide, South Australia
  • TDM model: 1991

Posted 20 May 2008 - 02:27 am

good.gif

I was asked recently for pics of my "cheap as" Carby Balancer that works a treat on the mighty Mk1.

Basically I follow the manual instructions with connections etc.

Materials needed:

1. 1 x metre length of timber (see photo)
2. 6 x metres of 4mm plastic hose not effected by fuel etc
3. small amount of auto trans fluid (coloured)
4. 3 x electrical dual cable holders & 3 nails to fix to timber
5. loop of wire at top & middle to hook balancer up to anything nearby eg handle bars etc to view levels easily

Here's the photos










In order to make any adjustments:

1. Warm engine up
2. switch the engine off each time, I've only needed to do this a few times so it doesn't effect the battery etc
3. remove airbox, (I'll assume you know how to get everything off to get to the airbox, if not read the manual)
4. twist the throttle enough to line up the adjusting screw between the carbies to make the very fine amounts needed,
5. make the adjustment,
6. twist the throttle to full on (but don't wring its neck), then release
7. replace airbox over carbies, (it does make a difference)you don't have to tighten
8. Restart engine & rev to around 4,000rpm or your cruising speed & hold to check levels in each tube are equal. If not repeat. I find that the levels may move slightly but close enough seems to work OK.
9. then put bike back together again & test on road.

I use 4mm plastic hose that's not effected by fuel etc, as it easily inserts into the bikes balancing hoses & creates a good seal with a bit of grease etc. I use enough length of hose so I can hook balancer onto either the handle bars or something nearby for easy viewing.

I use auto trans fluid for two reasons: 1. easy to see; 2. It won't hurt the motor if accidentally sucked in.


Happy cruising with a much smoother responsive motor with less vibrations. yahoo.gif

Cheers
drinks.gif

Edited by masterbrewer, 20 May 2008 - 07:24 am.


#2 dandywarhol

dandywarhol

    Carpe Citizen

  • Supporting Member(thanks)
  • PipPipPipPipPipPipPipPip
  • 5,324 posts
  • Location:Edinburgh, Scotland
  • TDM model: 2003

Posted 20 May 2008 - 09:02 am

Good job good.gif .......time you cleaned that Ayres Rock dust off yer door........ badgrock.gif

1967 Yamaha TD1C 250, 2014 Kawasaki W800, 2011 Aprilia Tuono 1000 V4, 2020 Yamaha XSR900

"At the cutting edge of technophobia" Scotland_180-animated-flag-gifs.gif mccoy.gif
 


#3 tdm850rider

tdm850rider

    Carpe Citizen

  • Member
  • PipPipPipPipPipPipPipPip
  • 6,103 posts
  • Location:Pittsburgh, Pennsylvania USA
  • TDM model: 1992

Posted 20 May 2008 - 09:58 am

Admin/Mods.. anyone else think this should go to KB?



Nice tutorial BTW.
Posted Image

Always tell the truth, it will gratify some of the people and astonish the rest. (Mark Twain)
£

Stebel Nautilus air-horn, Corbin seat, MRA Touring screen, single Delkevic silencer.
"I see by your outfit that you are a spaceman"(MkI (3VD) TDM Review)
Hints for using Carpe-TDM. (photo's, links, etc).

#4 JBX

JBX

    full o shoite

  • RTT manager(RTT)
  • 2,206 posts
  • Location:South France
  • TDM model: 2002

Posted 20 May 2008 - 01:43 pm

Great !

I'm about to do it the same way with some perfusion tubing...


Check THIS PAGE too, lots of ideas (it's in french but pics say it all).

top_640.png

 

 


#5 jht

jht

    has been here 4ever

  • Member
  • PipPipPipPipPipPipPipPip
  • 1,769 posts
  • Location:surrey/hants border
  • TDM model: 1996

Posted 20 May 2008 - 03:57 pm

QUOTE(tdm850rider @ Tue 20th May 2008, 10:43 AM) <{POST_SNAPBACK}>
Admin/Mods.. anyone else think this should go to KB?
Nice tutorial BTW.


Yup, stick it in there blink.gif

simple in that "why the bloody 'ell didnt I think of that" kinda way laugh.gif
Done: Homo sap navigation/ twisty thing on bars to make it go vroom/ grabby thing to make it stop (in front of twisty thing)/ 'leccy things front and rear to make it glow at night/ Sucky + drippy oiler thing to keep chains moist (!!) / Laser Pro Stock Race pipes / bleeding ear drums (see previous mod)
To do: Educate homo sap nav system to operate twisty + grabby things/ get ear plugs

All Trashed Now... Pants... its a Cat B Mwahahaha it lives again!!


Remember every driver is a deaf myoptic twat who is out to kill you, ALWAYS assume they are going to do THE most f*cking DUMBASS, STUPID manouver possible, at the worst possible moment; get past, and get past quick

#6 masterbrewer

masterbrewer

    has been here 4ever

  • Member
  • PipPipPipPipPipPipPipPip
  • 1,553 posts
  • Location:Adelaide, South Australia
  • TDM model: 1991

Posted 21 May 2008 - 10:33 pm

good.gif

That's what I thought too jht when I first came across it. blush.gif

drinks.gif

#7 Geordie Guy

Geordie Guy

    Carpe Citizen

  • Member
  • PipPipPipPipPipPipPipPip
  • 3,502 posts
  • Location:The Tyne - now ORMSKIRK
  • TDM model: 2010

Posted 21 May 2008 - 10:40 pm

Good bit of invention there.... good.gif


I'm a TDM SNOB !!!!     "Adventure before Dementia"  

Kawasaki GT550, XJ900 Diversion, 2002 TDM 900 , 2008 TDM 900a, 2010 TDM 900a.
 
 

#8 tdm850rider

tdm850rider

    Carpe Citizen

  • Member
  • PipPipPipPipPipPipPipPip
  • 6,103 posts
  • Location:Pittsburgh, Pennsylvania USA
  • TDM model: 1992

Posted 11 June 2009 - 09:51 pm

QUOTE(masterbrewer @ Mon 19th May 2008, 10:27 PM) <{POST_SNAPBACK}>
I use 4mm plastic hose that's not effected by fuel etc, as it easily inserts into the bikes balancing hoses & creates a good seal with a bit of grease etc. I use enough length of hose so I can hook balancer onto either the handle bars or something nearby for easy viewing.

Cheers
drinks.gif


Just one thing to clarify this, where are the balancing hoses? dry.gif
Posted Image

Always tell the truth, it will gratify some of the people and astonish the rest. (Mark Twain)
£

Stebel Nautilus air-horn, Corbin seat, MRA Touring screen, single Delkevic silencer.
"I see by your outfit that you are a spaceman"(MkI (3VD) TDM Review)
Hints for using Carpe-TDM. (photo's, links, etc).

#9 masterbrewer

masterbrewer

    has been here 4ever

  • Member
  • PipPipPipPipPipPipPipPip
  • 1,553 posts
  • Location:Adelaide, South Australia
  • TDM model: 1991

Posted 11 June 2009 - 11:34 pm

good.gif

QUOTE(tdm850rider @ Fri 12th Jun 2009, 08:21 AM) <{POST_SNAPBACK}>
Just one thing to clarify this, where are the balancing hoses? dry.gif

On my bike, I use the vacuum hose to the vacuum fuel pump & the other hose is a blanked off hose on the right side of the battery against the inside frame.

They both feed off the inlet manifolds.

Not perfect, but does a damn good job for $5. Good luck

drinks.gif



1 user(s) are reading this topic

0 members, 1 guests, 0 anonymous users